Labour Day Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: geek65

JN0-682 Data Center Professional (JNCIP-DC) Questions and Answers

Questions 4

Devices spine1 and spine have been configured as distributed Layer 3 gateways in the VXLAN topology, and devices leaf1 and leaf3 have been configured as layer 2 gateways. Device host must be able to communicate with device host?

Which two statements are true? (Choose two.)

Options:

A.

An IRB interface must be configured on device leaf1 and leaf2.

B.

An IRB interface must be configured on devices spine1 and spine2.

C.

Traffic from host1 to host2 will transmit the VXLAN tunnel from leaf1 to leaf3.

D.

Traffic from host1 to host will transit a VXLAN tunnel to spine or spine2 then a VXLAN from spine1 or spine2 to leaf 3.

Buy Now
Questions 5

Referring to the exhibit, you have a data center with two PODs. Seamless EVPN-VXLAN stitching is used to facilitate communication between the PODs.

Which three statements are true in this scenario? (Choose three.)

Options:

A.

AVXLAN tunnel can form between L2 and S1.

B.

A VXLAN tunnel can form between S1 and S2.

C.

AVXLAN tunnel can form between L1 and L2.

D.

AVXLAN tunnel can form between L2 and S3.

E.

AVXLAN tunnel can form between L1 and L4.

Buy Now
Questions 6

Which protocol is used between VCF member devices to create a loop-free topology?

Options:

A.

LLDP

B.

MDTP

C.

RSTP

D.

VCCP

Buy Now
Questions 7

The two data centers shown in the exhibit need to be connected using EVPN. Which two statements are correct in this situation? (Choose two.)

Options:

A.

Hosts in VLAN 10 can communicate with hosts in Data Center 2 using Layer 3.

B.

Hosts in VLAN 10 can communicate with hosts in Data Center 2 using Layer 2.

C.

Hosts in VLAN 202 can communicate using Layer 3 between data centers.

D.

Hosts in VLAN 202 can communicate using Layer 2 between data centers.

Buy Now
Questions 8

Referring to the exhibit, which statement is correct?

Options:

A.

Leaf1 has not learned any MAC addresses

B.

Leaf3 is the remote tunnel endpoint.

C.

One tunnel is servicing multiple VLANs

D.

Spanning Tree Protocol is disabled

Buy Now
Questions 9

You have a two spine and four leaf CRB topology and you must ensure that the hosts connected

to the leaf devices have reachability to all IRB interface addresses, including the local spine IRB

addresses, and the virtual gateway address.

Which two configuration parameters must be used to accomplish this task? (Choose two.)

Options:

A.

Configure a spine-to-spine BGP peering as part of the overlay.

B.

Configure virtual-gateway-accept-data under the IRB interface.

C.

Configure a spine-to-spine EVPN peering as part of the routing instance.

D.

Configure proxy-macip-advertisement under the IRB interface.

Buy Now
Questions 10

What are two types of EVPN routes? (Choose two.)

Options:

A.

ES-lmport route target

B.

Ethernet segment

C.

MAC mobility

D.

MAC advertisement

Buy Now
Questions 11

What is an advantage that EVPN has over VPLS when used for DCI?

Options:

A.

mass MAC withdrawal

B.

transparent BPDU transport

C.

active/standby multihoming

D.

reverse path forwarding

Buy Now
Questions 12

Referring to the exhibit,

what effect does EVPN core isolation have?

Options:

A.

Leaf 1 will send a pause frame to each connected host.

B.

Leaf 1 will place the interfaces to connected hosts into LACP passive mode.

C.

Leaf 1 will take down all revenue interfaces.

D.

Spine 1 will block all traffic.

Buy Now
Questions 13

Which two statements about the seamless EVPN-VXLAN stitching data center interconnect architecture are correct? (Choose two.)

Options:

A.

VXLAN stitching is supported in 3-stage and 5-stage fabrics.

B.

VXLAN stitching is ideal for medium and large data center designs.

C.

For Layer 2 stretched between data centers, a full mesh of VXLAN tunnels between leaf switches is required.

D.

IPIM is required in the underlay.

Buy Now
Questions 14

You need to add perimeter security to the network shown in the exhibit. All traffic must be inspected for attacks. The edge routers are using all available ports.Your solution must maintain both port and device resiliency.

In this scenario, which design would satisfy these requirements?

Options:

A.

one-arm SRX Series chassis cluster

B.

one-arm SRX Series device using LAG

C.

inline SRX Series chassis cluster

D.

inline SRX Series device using LAG

Buy Now
Questions 15

Which two combinations are supported when configuring a Virtual Chassis Fabric? (Choose two.)

Options:

A.

Four spine nods and 20 leaf nodes

B.

Four spine nods with 16 leaf nodes

C.

two spine nods and 16 leaf nodes

D.

Two spine and 28 leaf nodes

Buy Now
Questions 16

Referring to the exhibit,

which two statements are correct? (Choose two.)

Options:

A.

There are two tunnels to the remote endpoint.

B.

The irb. 0 interface is the remote tunnel endpoint interface.

C.

The source tunnel IP address is 192.168.100.11.

D.

There is one tunnel to the remote endpoint.

Buy Now
Questions 17

Which two statements about a DHCP relay in an EVPN-VXLAN fabric are correct? (Choose two.)

Options:

A.

The DHCP client and the DHCP server can reside in different routing instances.

B.

The DHCP client and the DHCP server must reside in the same routing instance.

C.

Anycast gateway addressing is not supported.

D.

Virtual gateway and anycast gateway addressing are both supported.

Buy Now
Questions 18

You are building an IP fabric underlay network for your new data center. You must ensure that you have predictable load-balancing behavior throughout your network. According to Juniper Networks, what are two best practices that should be followed in this scenario? (Choose two.)

Options:

A.

All leaf devices must be identical to the spine device models including the same installed line cards.

B.

All spine devices should be identical models including the same installed line cards.

C.

Every leaf device should have an identical uplink to every other leaf device.

D.

Every leaf device should have an identical uplink to every spine device.

Buy Now
Questions 19

You are logged in to Leaf 1. When examining the routing table, you notice that you have no

routes from Leaf 2.

Referring to the exhibit, which two commands would you use to troubleshoot the problem? (Choosetwo.)

Options:

A.

From Leaf 2, issue the show route advertising-protocol bgp 172.16.1.2 command.

B.

From Spine 1, issue the show route advertising-protocol bgp 172.16.1.1 command.

C.

From Spine 1, issue the show route advertising-protocol bgp 172.16.1.2 command.

D.

From Leaf 1, issue the show route receive-protocol bgp 172.16.1.1 command.

Buy Now
Questions 20

You are considering deploying a MAC-VRF type routing instance with a VLAN-bundle service

type. In this scenario, which two statements are correct? (Choose two.)

Options:

A.

It can be implemented in a bridge overlay architecture.

B.

VLAN normalization is supported.

C.

Multiple VLAN IDs per EVI are supported.

D.

It can be implemented in an ERB architecture.

Buy Now
Questions 21

Which EVPN route type would be used in DCI situation in which the IP subnets between data center are complete unique?

Options:

A.

Type 4

B.

Type 3

C.

Type 2

D.

Type 5

Buy Now
Questions 22

What are two streaming data formats supported for network analytics? (Choose two.)

Options:

A.

GPB

B.

XML

C.

JSON

D.

SLAX

Buy Now
Questions 23

Referring to the exhibit, which statement is correct?

Options:

A.

The exhibit shows a 5-stage IP fabric architecture.

B.

The exhibit shows a collapsed fabric architecture.

C.

The exhibit does not represent a valid fabric architecture.

D.

The exhibit shows a 3-stage IP fabric architecture.

Buy Now
Questions 24

You are an engineer for a hosting company. You have a new customer that wants the ability to

connect any VLAN on any port. They want to have all VLANs map to a single bridge domain and EVPN instance (EVI). They control all their own routing and just need the connectivity.

Which two parameters should you configure to achieve these goals? (Choose two.)

Options:

A.

instance-type mac-vrf

B.

service-type vlan-aware

C.

service-type vlan-bundle

D.

instance-type virtual-switch

Buy Now
Questions 25

What are two methods used to scale an IBGP IP Fabric? (Choose two.)

Options:

A.

Spanning tree

B.

Redundant trunk groups

C.

Route reflection

D.

Confederations

Buy Now
Questions 26

You are asked to enable visibility into your EVPN-VXLAN network traffic by monitoring traffi

continuously. Which two statements are correct in this scenario? (Choose two.)

Options:

A.

You cannot enable sFlow monitoring on each interface individually.

B.

The sFlow agent is installed by default on your OFX Series switch.

C.

You must enable sFlow monitoring on each interface individually.

D.

The sFlow agent needs to be manually installed on your QFX Series switch.

Buy Now
Questions 27

You are asked to deploy an Ethernet bridging design in a data center with the criteria shown

below.

-Routing must occur on the spine devices.

-VTEPs must terminate on the leaf devices.

-Facilitate inter-VLAN communication.

-Layer 2 gateways must be present on spine and leaf devices.

Which architecture should you use in this scenario?

Options:

A.

edge-routed bridging architecture

B.

centrally-routed bridging architecture

C.

bridge overlay architecture

D.

collapsed spine architecture

Buy Now
Questions 28

What is the purpose of the command shown in the exhibit?

Options:

A.

To stop the reception of transit multicast traffic when there are no interested receivesattached to the local VTEP

B.

To disable the group2390.0.1 across the entire VXLAN.

C.

To stop the transmission of transit multicast traffic when there are no interested receives attached to a remote VTEP

D.

To disallow IGMP request for the group 239.0.01 from host attached to the local VTEP

Buy Now
Questions 29

You are attempting to configure filter-based forwarding in your data center. All traffic from Host1

that is going to Host2 should be inspected by the data center firewall. You have verified that the traffic is being forwarded from router leaf L1's VRF-1 to its INSPECT-VRF.However, the traffic is not reaching service L2.

Referring to the exhibit, which two steps should you take to troubleshoot the problem? (choose two.)

Options:

A.

Examine the INSPECT-VRF.evpn 0 route table on L1 for a default route that will direct the traffic to L2.

B.

Examine the INSPECT-VRF.inet. 0 route table on L1 for a default route that will direct the traffic to L2.

C.

Ensure that VRF-1 and INSPECT-VRF route targets on L1 and L2 match.

D.

Ensure that the route target in the INSPECT-VRF of L1 matches the route target of the INSPECT- VRF of L2.

Buy Now
Questions 30

You have configured a new MC-LAG connection to a host. After committing the configuration, the

MC-LAG link is not functioning properly.

Referring to the exhibit, how would you solve this problem?

Options:

A.

Configure a system-id on qfx1 that is different from the system-id on qfx2

B.

Change the mc-ae is on qfx1 to 1

C.

Configure status-control on qfx2 to active

D.

Change the chassis on qfx1 to 1

Buy Now
Questions 31

Which two statements about an over-the-top (OTT) data center interconnect architecture are correct? (Choose two.)

Options:

A.

For a Layer 2 stretched network between data centers, a full mesh of VXLAN tunnels between leaf switches is required.

B.

IBGP or EBGP is required for the underlay.

C.

Multicast is supported.

D.

OTT is ideal for small and medium data center designs.

Buy Now
Questions 32

The configuration shown in the exhibit is intended to set up assisted replication but will not

commit. Which action will create a valid configuration in this situation?

Options:

A.

Change the 10.0 address to 192.168.100.1 primary.

B.

Change the replicator inet address to 192.168.100.101.

C.

Delete replicator inet 192.168.100.1.

D.

Change the replicator inet address to 192.168.100. 51.

Buy Now
Questions 33

After configuring an IP fabric using EBGP as you protocol, you notice that not all of the routers are showing up in the routing tables. You have verified that all adjacencies have formed, and place and configured properly.

In this scenario, which statement is true?

Options:

A.

The routers have not been configured with the multipath multiple-as parameter.

B.

The routers have not been configured using the bfd-1 Liveness-detection parameter.

C.

The routers have not been configured using the multihop parameter.

D.

The routers have not been configured using the add-path parameter

Buy Now
Questions 34

You have deployed two data centers that require a Layer 2 stretch between host1 and host2.

Referring to the exhibit, what does a Layer 2 stretch require?

Options:

A.

A VPLS WAN connection data centers

B.

A VXLAN tunnel originating on VTEP1 to VTEP2

C.

A VXLAN tunnel originating on the super Spine Layer in DC1 to the Super Spine Layer in DC2

D.

A VXLAN tunnel originating on the Spine Layer in DC1 to the Spine Layer in DC2.

Buy Now
Questions 35

When using EBGP as the underlay protocol for your IP fabric architecture, which two statements

are true? (Choose two.)

Options:

A.

Spine nodes peer to both leaf and spine nodes

B.

Leaf nodes only peer to spine nodes

C.

Leaf nodes peer to both spine and leaf nodes

D.

Spine nodes only peer to leaf nodes

Buy Now
Questions 36

Which three statements are correct about multitenancy in a Junos EVPN environment? (Choose three.)

Options:

A.

MAC-VRF instances allow for overlapping routes and VLANs.

B.

MAC-VRF instances allow for varying EVPN services on the same device.

C.

VRF instances allow for overlapping subnets.

D.

Virtual switch instances allow for varying EVPN services on the same device.

E.

Virtual switch instances allow for overlapping VLANs.

Buy Now
Questions 37

Which statement is true about the route shown in the exhibit?

Options:

A.

The route target on this route is 1000

B.

The route is an EVPN type-1 route.

C.

The route uses a type-1 route distinguisher.

D.

The VNI for this route is 304.

Buy Now
Questions 38

Which EVPN router type prevents BUM traffic from looping back to a multihued host?

Options:

A.

Ethernet segment router

B.

IP prefix route

C.

Ether auto discovery route

D.

Inclusive multicast-Ethernet tag route

Buy Now
Questions 39

Which two statements about the seamless EVPN-VXLAN stitching interconnect gateways are correct? (Choose two.)

Options:

A.

IBGP is recommended for VXLAN stitching overlays.

B.

Interconnect gateways will rewrite the route target, route distinguisher. and ESI values for each stretched virtual network.

C.

All EVPN routes types are forwarded among interconnect gateways in a full-mesh manner.

D.

The interconnect gateway can reside on the super spine layer of a multi-POD data center.

Buy Now
Questions 40

You are configuring an MX Series router to act as a Layer 3 gateway to route traffic between VXLANs in different data centers across a WAN connection. In this scenario, what must you do to enable this communication?

Options:

A.

Configure route reflectors.

B.

Change the UDP port used by the VXLANs.

C.

Configure the IRB interfaces to connect the VXLANs.

D.

Enable PIM on all interfaces.

Buy Now
Questions 41

What are three functions supported by the Contrail Command user interface?

Options:

A.

Integrated syslog collector

B.

Enabling VM-to-BMS bridging

C.

Configuring management domains

D.

Onboarding of an IP fabric

E.

Creating virtual network

Buy Now
Questions 42

You must advertise reachability between two firewalls with unique IP subnets that terminate security services through your EVPN-VXLAN environment.

In this scenario, which EVPN route type should you enable to accomplish this task?

Options:

A.

type-4

B.

type-2

C.

type-5

D.

type-3

Buy Now
Questions 43

You work in a data center where VMs and hosts are frequently moved. Your design needs to eliminate inefficient traffic flows.

In this scenario, which two solutions will satisfy this requirement? (Choose two.)

Options:

A.

VXLAN

B.

EVPN

C.

VMTO

D.

VPLS

Buy Now
Questions 44

The MC-LAG group shown in the exhibit is providing high availability services for the directly connected servers. The backup liveness detection is applied to the ICL-PL link, however, when oneof the members rebooted, there was traffic loss for a few seconds.

In this scenario, where should you apply the backup liveness detection?

Options:

A.

On the management interfaces

B.

On the ae2 interface

C.

On the ae1 interface

D.

On the ae0 interface

Buy Now
Questions 45

Which event triggers the generation of a EVPN type-4 route?

Options:

A.

When unknown unicast traffic is received on an interface.

B.

When known unicast traffic is received on an interface.

C.

When a new VNI is configured.

D.

When a new ESI is configured.

Buy Now
Questions 46

Which IP fabric underlay protocol provides the highest degree of scalability?

Options:

A.

IS-IS

B.

RIP

C.

EBGP

D.

OSPF

Buy Now
Exam Code: JN0-682
Exam Name: Data Center Professional (JNCIP-DC)
Last Update: May 1, 2024
Questions: 154
JN0-682 pdf

JN0-682 PDF

$28  $80
JN0-682 Engine

JN0-682 Testing Engine

$33.25  $95
JN0-682 PDF + Engine

JN0-682 PDF + Testing Engine

$45.5  $130