Which command set configures a Cisco Catalyst 9800 Series Wireless Controller so that the client traffic enters the network at the AP switch port?

A wireless controller has a RADIUS server configured globally. Another RADIUS server is mapped for WLAN A in this controller. Which RADIUS server does the controller use for authenticating clients from WLAN A?
A customer has Cisco FlexConnect APs at all remote branches and requires zero downtime through the FlexConnect Fault Tolerance feature. Which two configurations must be identical on both controllers to maintain connectivity when the APs switch from the primary WLC to the backup WLC because of a WAN failure? (Choose two.)
An organization is concerned about site-specific 802.1X authentication in the event of a WAN outage in their Cisco FlexConnect deployment. Which data is needed to accomplish this authentication?
An engineer is troubleshooting a Cisco CMX high-availability deployment and notices that the primary and backup Cisco CMX servers are both considered primary. Which command must the engineer run on the backup server?
A consulting engineer must migrate the APs from a Cisco 8540 WLC to a Cisco Catalyst 9800-80 WLC. As part of the migration, the engineer is advised to use a policy map as part of the configuration on the Catalyst 9800-80 WLC to mirror the platinum QoS settings on voice WLAN to accommodate CP-840 wireless phones. Which configuration must the engineer implement on the voice WLAN?


An engineer must implement intrusion protection on the WLAN. The AP coverage is adequate and on-channel attacks are the primary concern. The building is historic, which makes adding APs difficult. Which AP mode and submode must be implemented?
Refer to the exhibit.
The security team has implemented ISE as an AAA solution for the wireless network. The wireless engineer notices that though clients are able to authenticate successfully, the ISE policies that are designed to place them on different interfaces are not working. Which configuration must be applied in the RADIUS Authentication Settings section from the ISE Network Device page?

A customer configures iPSK for use with a Cisco Catalyst 9800 Series controller. The configuration is complete, but the wireless client fails to authenticate to the network. Which implementation resolves this issue?
What two actions must be taken by an engineer configuring wireless Identity-Based Networking for a WLAN to enable VLAN tagging? (Choose two.)
An engineer configures custom QoS mapping on a Cisco Catalyst 9800 Series Wireless Controller. The engineer uses the Cisco-recommended configuration for DSCP-to-UP mapping. Which two wired-to-wireless QoS mappings should be configured? (Choose two.)
An engineer wants to upgrade the APs in a Cisco FlexConnect group. To accomplish this upgrade, the FlexConnect AP Upgrade setting will be used. One AP of each model with the lowest MAC address in the group must receive the upgrade directly from the controller. Which action accomplishes this direct upgrade?
Which three properties are used for client profiling of wireless clients? (Choose three.)
A customer must use deep-packet inspection on the Cisco Catalyst 9800 Series Wireless Controller. The details must include all wireless client use details. Where must AVC be configured to meet this requirement?
A retail company has deployed a FlexConnect WLAN with local switching at a small branch location. The Flex profile already includes VLAN 1950 and is mapped to the correct site tag. A specific client must be dynamically assigned to VLAN 1950 by Cisco ISE, and that client’s traffic must be centrally switched to the controller.
Which two configurations must the engineer enable on the controller? (Choose two.)
An engineer completed the basic installation for two Cisco CMX servers and is in the process of configuring high availability, but it fails. Which two statements about the root of the issue are true? (Choose two.)
An engineer configures Cisco CMX. which uses Layer 2 high availability on primary and secondary CMX instances, according to these specifications:
· Primary CMX IP address: 192.168.1.4/24
· Secondary CMX IP address 192 168.4.4/24
· Virtual IP address: 192.168.4.1/24
in testing, the engineer discovers that the failover fails. Which action resolves the issue?
A shopping center uses AireOS controllers with Cisco Wave 2 APs. A separate WLAN named Guest-012345678-WLAN is used for guest wireless clients. Management needs location analytics to determine popular areas. CMX must track only associated clients. What must be selected on the CMX server settings?
Refer to the exhibit. An event company must gather location-tracking details of wireless clients at an event where clients will be given free guest access to the Wi-Fi. A network engineer must integrate a Cisco WLC with a Cisco CMX server. Which command must be run?

When the Cisco FlexConnect AP Image Upgrade feature is used, APs must communicate with each other to distribute the image. Which two elements are required for this feature to work when the APs are on different subnets? (Choose two.)
A wireless administrator must assess the different client types connected to Cisco Catalyst 9800 Series Wireless Controller without using any external servers. Which configuration must be added to the controller to achieve this assessment?
For security purposes, an engineer enables CPU ACL and chooses an ACL on the Security > Access Control Lists > CPU Access Control Lists menu. Which kind of traffic does this change apply to as soon as the change is made?
A customer must provide remote users with secure wireless access through a Cisco Catalyst 9800 Series Wireless Controller and Cisco APs. The corporate WLAN must be extended over the Internet to specific locations and support a locally installed IP phone.
Which two actions accomplish this configuration? (Choose two.)
All APs are receiving multicast traffic, instead of only the APs that need it. What is the cause of this problem?
The security policy mandates that only controller web management traffic is allowed from the IT subnet. In testing, an engineer is trying to connect to a WLAN with Web Authentication for guest users, but the page is timing out on the wireless client browser. What is the cause of the issue?
Which feature on the Cisco Wireless LAN Controller must be present to support dynamic VLAN mapping?
An IT team is growing quickly and needs a solution for management device access. The solution must authenticate users from an external repository instead of the current local on the WLC, and it must also identify the user and determine what level of access users should have. Which protocol do you recommend to achieve these goals?